急求一篇5000字的模具专业英语文章(带中文翻译),哪位大神给力啊!

 我来答
匿名用户
2013-11-23
展开全部
Extrusion molding process
Thermoplastic plastic extrusion molding process is divided into four stages lesson.
Plasticizing stage
Through dry processing plastic raw materials by extruder hopper to join a nitrogen-treated barrel nitrogen-treated barrel, after the heating and screw rotation, compaction and the mixing action below, by solid powder or aggregates into uniform melt with some liquidity for the process plastication.
Extrusion stage
Even with the plastic melt plastication screw rotation was sent to a nitrogen-treated barrel in front, screw rotation extrusion action by extrusion die, on a certain shape mouth mode and get section and mouth model shape continuous profiles consistent.
Finalizes the design phase
Thermoplastic plastics in leave immediately after mouth mode, extruded plastic continuous profiles for cooling and finalize the design, or plastic in self-respect under the action of will deformation, appear sag or distortion phenomenon.
In most cases, qualitative and cooling is finish at the same time, only in extrusion various bar stock and pipe, just have a separate qualitative process, and the extrusion film, finalize the design process, no single etc, if only by cooling can be. Extrusion plank and sheet, sometimes by a pair of roller planish, while rise to finalize the design and cooling effect. Cooling generally USES air cooling or water cooling, cooling speed on the plastic parts surface roughness, size shape accuracy etc performance has very big effect. Hard plastics (such as polystyrene, low density polyethylene and rigid PVC etc.) can't cooling too fast, otherwise easy to cause the residual stress, and affect the appearance of plastic parts quality; Soft or crystallization type requires plastic parts in time, lest plastics deformation cooling.
Traction plastic parts. Coiling and cutting
Plastics extruding the mouth mode since, usually because of pressure from mold and happen suddenly lifted after inflation phenomenon, and cooling shrinks will happen again, thus make the size and shape of the plastic parts changes. In addition, because plastics was continuous extrusion, self-respect is more and more big, if not guidance, can cause plastics stagnation, make plastic thing cannot be smooth extrusion. Therefore, in the cooling at the same time, we should continuously will plastics derivation, this is traction.
Traction process one by extruder auxiliary device to complete. Traction Traction with extrusion

人教版新目标初二下英语同步辅导(一)初中二年级下un...初中二年级下Un...

speed speed will adapt to, general traction speed slightly higher than the extrusion speed, so as to eliminate the plastics dimension change, at the same time for plastics proper stretching can improve the molding quality. Different plastics traction at different speeds. Usually film and monofilament traction speed can be quicker, its reason is drawing speed, the plastic parts decreased diameter and thickness, longitudinal strength increases, elongation fracture resistance reduction. For extrusion hard plastic parts, traction speed cannot big, usually takes will drag speed regulation within a certain range, and to be very evenly, otherwise it will affect its size uniformity and mechanical properties.
Through the plastics class traction in cutting device according to use requirement on cutting (such as rods, tubes, plate, sheet etc), or in coiling device made around a roll (such as film, monofilament, cables, etc). In addition, some plastic parts such as films etc, sometimes need to undertake post-processing, in order to improve dimensional stability.
匿名用户
2013-11-23
展开全部
2011-03-15 21:38One early use of the term "personal computer" appeared in a November 3, 1962, New York Times article reporting John W. Mauchly's vision of future computing as detailed at a recent meeting of the American Institute of Industrial Engineers. Mauchly stated, "There is no reason to suppose the average boy or girl cannot be master of a personal computer.
Six years later a manufacturer took a risk at referring to their product this way when Hewlett Packard advertised their "Powerful Computing Genie" as "The New Hewlett Packard 9100A personal computer".This advertisement was deemed too extreme for the target audience and replaced with a much drier ad for the HP 9100A programmable calculator.
During the next seven years the phrase had gained usage so when Byte magazine, published its first edition it referred to its readers as being in the "personal computing field", while Creative Computing defined the personal computer as a "non-(time)shared system containing sufficient processing power and storage capabilities to satisfy the needs of an individual user."Two years later when the 1977 Trinity of preassembled small computers hit the markets, the Apple II and the PET 2001 were advertised as personal computers, while the TRS-80 was a microcomputer used for household tasks including "personal financial management". By 1979 over half a million microcomputers were sold and the youth of the day had a new concept of the personal computer.
On January 3 1983, the Personal Computer was the first non-human to be announced as Person of the Year by Time Magazine, in 1982.
The initialism PC may refer generically to a personal computer, or may be intended to refer to one of the original IBM PC compatible computers, or may refer to a Microsoft Windows computer currently available.
已赞过 已踩过<
你对这个回答的评价是?
评论 收起
推荐律师服务: 若未解决您的问题,请您详细描述您的问题,通过百度律临进行免费专业咨询

为你推荐:

下载百度知道APP,抢鲜体验
使用百度知道APP,立即抢鲜体验。你的手机镜头里或许有别人想知道的答案。
扫描二维码下载
×

类别

我们会通过消息、邮箱等方式尽快将举报结果通知您。

说明

0/200

提交
取消

辅 助

模 式