Question

跪求，基于AT89S52连接SHT11的温湿度采集程序（C语言的），急！急！急！

毕业设计，网上死活找不到完整的程序，无奈啊。有程序的兄弟姐妹麻烦贡献哈，或发至我的邮箱wxg19861112@sina.com，先谢谢大家啦！！！一定要C语言的啊！！！
SHT10和SHT11程序通用

Answer 1

sbit SCK = P3^5; //定义通讯时钟端口
sbit DATA = P3^6; //定义通讯数据端口

typedef union
{ unsigned int i; //定义了两个共用体
float f;
} value;

enum {TEMP,HUMI}; //TEMP=0,HUMI=1

#define noACK 0 //用于判断是否结束通讯
#define ACK 1 //结束数据传输
//adr command r/w
#define STATUS_REG_W 0x06 //000 0011 0
#define STATUS_REG_R 0x07 //000 0011 1
#define MEASURE_TEMP 0x03 //000 0001 1
#define MEASURE_HUMI 0x05 //000 0010 1
#define RESET 0x1e //000 1111 0

/****************定义函数****************/
void s_transstart(void); //启动传输函数
void s_connectionreset(void); //连接复位函数
char s_write_byte(unsigned char value);//DHT90写函数
char s_read_byte(unsigned char ack); //DHT90读函数
char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode);//测量温湿度函数
void calc_dht90(float *p_humidity ,float *p_temperature);//温湿度补偿

/*--------------------------------------
;模块名称:s_transstart();
;功 能:启动传输函数
;-------------------------------------*/
void s_transstart(void)
// generates a transmission start
// _____ ________
// DATA: |_______|
// ___ ___
// SCK : ___| |___| |______
{
DATA=1; SCK=0; //Initial state
_nop_();
SCK=1;
_nop_();
DATA=0;
_nop_();
SCK=0;
_nop_();_nop_();_nop_();
SCK=1;
_nop_();
DATA=1;
_nop_();
SCK=0;
}

/*--------------------------------------
;模块名称:s_connectionreset();
;功 能:连接复位函数
;-------------------------------------*/
void s_connectionreset(void)
// communication reset: DATA-line=1 and at least 9 SCK cycles followed by transstart
// _____________________________________________________ ________
// DATA: |_______|
// _ _ _ _ _ _ _ _ _ ___ ___
// SCK : __| |__| |__| |__| |__| |__| |__| |__| |__| |______| |___| |______
{
unsigned char i;
DATA=1; SCK=0; //Initial state
for(i=0;i<9;i++) //9 SCK cycles
{
SCK=1;
SCK=0;
}
s_transstart(); //transmission start
}

/*--------------------------------------
;模块名称:s_write_byte();
;功 能:SHT10写函数
;-------------------------------------*/
char s_write_byte(unsigned char value)
//----------------------------------------------------------------------------------
// writes a byte on the Sensibus and checks the acknowledge
{
unsigned char i,error=0;
for (i=0x80;i>0;i/=2) //shift bit for masking
{
if (i & value) DATA=1; //masking value with i , write to SENSI-BUS
else DATA=0;
SCK=1; //clk for SENSI-BUS
_nop_();_nop_();_nop_(); //pulswith approx. 3 us
SCK=0;
}
DATA=1; //release DATA-line
SCK=1; //clk #9 for ack
error=DATA; //check ack (DATA will be pulled down by DHT90),DATA在第9个上升沿将被DHT90自动下拉为低电平。
_nop_();_nop_();_nop_();
SCK=0;
DATA=1; //release DATA-line
return error; //error=1 in case of no acknowledge //返回：0成功，1失败
}

/*--------------------------------------
;模块名称:s_read_byte();
;功 能:SHT10读函数
;-------------------------------------*/
char s_read_byte(unsigned char ack)
// reads a byte form the Sensibus and gives an acknowledge in case of "ack=1"
{
unsigned char i,val=0;
DATA=1; //release DATA-line
for (i=0x80;i>0;i/=2) //shift bit for masking
{ SCK=1; //clk for SENSI-BUS
if (DATA) val=(val | i); //read bit
_nop_();_nop_();_nop_(); //pulswith approx. 3 us
SCK=0;
}
if(ack==1)DATA=0; //in case of "ack==1" pull down DATA-Line
else DATA=1; //如果是校验(ack==0)，读取完后结束通讯
_nop_();_nop_();_nop_(); //pulswith approx. 3 us
SCK=1; //clk #9 for ack
_nop_();_nop_();_nop_(); //pulswith approx. 3 us
SCK=0;
_nop_();_nop_();_nop_(); //pulswith approx. 3 us
DATA=1; //release DATA-line
return val;
}

/*--------------------------------------
;模块名称:s_measure();
;功 能:测量温湿度函数
;-------------------------------------*/
char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode)
// makes a measurement (humidity/temperature) with checksum
{
unsigned error=0;
unsigned int i;

s_transstart(); //transmission start
switch(mode){ //send command to sensor
case TEMP : error+=s_write_byte(MEASURE_TEMP); break;
case HUMI : error+=s_write_byte(MEASURE_HUMI); break;
default : break;
}
for (i=0;i<65535;i++) if(DATA==0) break; //wait until sensor has finished the measurement
if(DATA) error+=1; // or timeout (~2 sec.) is reached
*(p_value) =s_read_byte(ACK); //read the first byte (MSB)
*(p_value+1)=s_read_byte(ACK); //read the second byte (LSB)
*p_checksum =s_read_byte(noACK); //read checksum
return error;
}

/*--------------------------------------
;模块名称:calc_dht90();
;功 能:温湿度补偿函数
;-------------------------------------*/
void calc_dht90(float *p_humidity ,float *p_temperature)
// calculates temperature [C] and humidity [%RH]
// input : humi [Ticks] (12 bit)
// temp [Ticks] (14 bit)
// output: humi [%RH]
// temp [C]
{ const float C1=-4.0; // for 12 Bit
const float C2=+0.0405; // for 12 Bit
const float C3=-0.0000028; // for 12 Bit
const float T1=+0.01; // for 14 Bit @ 5V
const float T2=+0.00008; // for 14 Bit @ 5V

float rh=*p_humidity; // rh: Humidity [Ticks] 12 Bit
float t=*p_temperature; // t: Temperature [Ticks] 14 Bit
float rh_lin; // rh_lin: Humidity linear
float rh_true; // rh_true: Temperature compensated humidity
float t_C; // t_C : Temperature [C]

t_C=t*0.01 - 40; //calc. temperature from ticks to [C]
rh_lin=C3*rh*rh + C2*rh + C1; //calc. humidity from ticks to [%RH]
rh_true=(t_C-25)*(T1+T2*rh)+rh_lin; //calc. temperature compensated humidity [%RH]
if(rh_true>100)rh_true=100; //cut if the value is outside of
if(rh_true<0.1)rh_true=0.1; //the physical possible range

*p_temperature=t_C; //return temperature [C]
*p_humidity=rh_true; //return humidity[%RH]
}

Answer 2

没有sht11，只有sht10的 我这里有SHT10的C程序