翻译一段话,谢谢
整体产品分三步完成:1)接受可燃气体探测报警、火灾报警,联动的基本功能和气体灭火控制功能;2)采用触摸屏记录实时火灾报警,气体浓度等信息,并将相关报警信息传输给客户端;3...
整体产品分三步完成:
1)接受可燃气体探测报警、火灾报警,联动的基本功能和气体灭火控制功能;
2)采用触摸屏记录实时火灾报警,气体浓度等信息,并将相关报警信息传输给客户端;
3)完成相应国家标准要求的全部功能。
控制柜要求如下:
1) 具有主备电源自动切换功能,当主电源断电时,备用电源自动投入,当主电源恢复时,自动断开备用电源,并自动投入主电源。控制柜内配置专用电源。且DC24V、AC220电源故障状态均有显示,同时向控制中心送出2组无源干接点信号(电源故障、CO2系统故障1)。
2) 具有自动、手动两种操作方式。
当系统处于手动方式时,火灾报警控制柜接收外部探测器火警信息逻辑组合信号后,只能报警,不能启动灭火装置。只有在控制柜触摸屏上启停灭火区域,触摸屏上设置三个区域的释放开关。
当系统处于自动方式时,火灾报警控制柜接收火警逻辑组合信号或按下相应区域的手动报警按钮后,控制柜先发出声光报警信号,延时30秒后,若没有停止命令,即发出命令启动灭火装置。
3) 有故障或火警信号时,控制柜内发出声光报警信号,故障声为短音,火警声为长音。按下消音按钮,可消除声响,同时消音灯亮。 展开
1)接受可燃气体探测报警、火灾报警,联动的基本功能和气体灭火控制功能;
2)采用触摸屏记录实时火灾报警,气体浓度等信息,并将相关报警信息传输给客户端;
3)完成相应国家标准要求的全部功能。
控制柜要求如下:
1) 具有主备电源自动切换功能,当主电源断电时,备用电源自动投入,当主电源恢复时,自动断开备用电源,并自动投入主电源。控制柜内配置专用电源。且DC24V、AC220电源故障状态均有显示,同时向控制中心送出2组无源干接点信号(电源故障、CO2系统故障1)。
2) 具有自动、手动两种操作方式。
当系统处于手动方式时,火灾报警控制柜接收外部探测器火警信息逻辑组合信号后,只能报警,不能启动灭火装置。只有在控制柜触摸屏上启停灭火区域,触摸屏上设置三个区域的释放开关。
当系统处于自动方式时,火灾报警控制柜接收火警逻辑组合信号或按下相应区域的手动报警按钮后,控制柜先发出声光报警信号,延时30秒后,若没有停止命令,即发出命令启动灭火装置。
3) 有故障或火警信号时,控制柜内发出声光报警信号,故障声为短音,火警声为长音。按下消音按钮,可消除声响,同时消音灯亮。 展开
2个回答
2011-05-04
展开全部
Whole product completed: into three
1) accept flammable gas detection alarm, fire alarm, the basic function and linkage of gas fire-extinguishing control functions;
2) using real-time fire alarm, touch-screen record gas concentrations, and related information such as alarming information transmission give the client;
3) complete corresponding all of the functions of national standards.
Cabinet requirement as follows:
1) for electrical automatic switch with the Lord, when the mains power function, alternate power auto-cast, when the mains recovers, automatically disconnect standby power, and the main power auto-cast. Control cabinet with special power supply. And AC220 power fault state DC24V, are to control center display, but also sent out two groups passive dry contact signal (power failure, CO2 system fault 1).
2) with automatic and manual two kinds of operating mode.
When the system is in manual mode, fire alarm controller receive external probe fire information only logical combinations signal, police, cannot start the fire extinguishing devices. Only in the start-stop control touch screen, touch screen set on fire area of three areas release switch.
When the system is in automatic mode, fire alarm controller receives fire logical combination signal or press the corresponding regional manual alarm button, control cabinet after first give out sound and light alarm signal, delay after 30 seconds, if not stop command, namely commands start fire extinguishing devices.
3) have fault or the fire alarm, the control cabinet give out sound and light alarm signal, fault for listeners, fire acoustic sound for drawl. Press censored button, can eliminate noise, and also censored emit light.
1) accept flammable gas detection alarm, fire alarm, the basic function and linkage of gas fire-extinguishing control functions;
2) using real-time fire alarm, touch-screen record gas concentrations, and related information such as alarming information transmission give the client;
3) complete corresponding all of the functions of national standards.
Cabinet requirement as follows:
1) for electrical automatic switch with the Lord, when the mains power function, alternate power auto-cast, when the mains recovers, automatically disconnect standby power, and the main power auto-cast. Control cabinet with special power supply. And AC220 power fault state DC24V, are to control center display, but also sent out two groups passive dry contact signal (power failure, CO2 system fault 1).
2) with automatic and manual two kinds of operating mode.
When the system is in manual mode, fire alarm controller receive external probe fire information only logical combinations signal, police, cannot start the fire extinguishing devices. Only in the start-stop control touch screen, touch screen set on fire area of three areas release switch.
When the system is in automatic mode, fire alarm controller receives fire logical combination signal or press the corresponding regional manual alarm button, control cabinet after first give out sound and light alarm signal, delay after 30 seconds, if not stop command, namely commands start fire extinguishing devices.
3) have fault or the fire alarm, the control cabinet give out sound and light alarm signal, fault for listeners, fire acoustic sound for drawl. Press censored button, can eliminate noise, and also censored emit light.
已赞过
已踩过<
评论
收起
你对这个回答的评价是?
推荐律师服务:
若未解决您的问题,请您详细描述您的问题,通过百度律临进行免费专业咨询