Question

有哪位大侠知道protel99se中的原理图的错误怎么改呀？非常感谢！！！！！

错误如下：
D1 Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.
D1 Error: Part type must be entered in READ ONLY field 1: type=<part type>(<spice prefix>)
D1 Error: Netlist data must be entered in READ ONLY field 5: netlist=<netlist data>
C1 Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.
C1 Error: Part type must be entered in READ ONLY field 1: type=<part type>(<spice prefix>)
C1 Error: Netlist data must be entered in READ ONLY field 5: netlist=<netlist data>
R1 Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.
R1 Error: Part type must be entered in READ ONLY field 1: type=<part type>(<spice prefix>)
R1 Error: Netlist data must be entered in READ ONLY field 5: netlist=<netlist data>
Setup Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.
Setup Error: Designation ATTRIBUTE must be entered.
Setup Error: Part type must be entered in READ ONLY field 1: type=<part type>(<spice prefix>)
Setup Error: Netlist data must be entered in READ ONLY field 5: netlist=<netlist data>
Setup Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.
Setup Error: Designation ATTRIBUTE must be entered.
Setup Error: Part type must be entered in READ ONLY field 1: type=<part type>(<spice prefix>)
Setup Error: Netlist data must be entered in READ ONLY field 5: netlist=<netlist data>
Setup Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.
Setup Error: Designation ATTRIBUTE must be entered.
Setup Error: Part type must be entered in READ ONLY field 1: type=<part type>(<spice prefix>)
Setup Error: Netlist data must be entered in READ ONLY field 5: netlist=<netlist data>
Setup Error: Pin order data (PINS=1:[<pins>]) not in READ ONLY field 4. Pins sorted by pin-name.

Answer 1

兄弟啊，这问题是你原理图中封装PIN号与PCB封装的PIN号不对应造成的，你具体看看，我英文有些个差，就大体上分析就是这样的......,要不改原理图封装PIN位名称，要么改PCB元件封装PIN号名称中的一种,要求对位的位号与名称要统一才OK，希望能够帮助到你，祝你成功.....!

追问

恩恩，谢谢你

追答

搞定没有，

Answer 2

你软件没装好吧？没见过有这样的错误出现。

追问

额...装好了呀，是原理图本身有错误，比如说原件封装什么的，不知道怎么改。。。。。你看得懂这些错误的英文么？？求帮忙额。。。。

追答

要不你把文件传给我，我帮你看看，因为错误这么多，我没遇到过，不了解具体情况。

追问

怎么传呀？反正点仿真运行的话就会生成提示哪里有错误的文件，里面好多错误。。。

追答

仿真？？？你用3D看立体的是吧？你把你QQ告诉我，然后加你QQ

追问

恩恩。。。。谢谢你925281287