Question

哪位好心人帮我用英文翻译一下 谢谢

摘要
本设计为连接垫片的冷冲压设计，根据设计零件的尺寸、材料、批量生产等要求，首先分析零件的工艺性，确定冲裁工艺方案及模具结构方案，然后通过工艺设计计算，确定排样和裁板，计算冲压力和压力中心，初选压力机，计算凸、凹模刃口尺寸和公差，最后设计选用零、部件，对压力机进行校核，绘制模具总装草图，以及对模具主要零件的加工工艺规程进行编制。其中在结构设计中，主要对凸模、凹模、凸凹模、定位零件、卸料与顶出件装置、模架、冲压设备、紧固件等进行设计，对于部分零件选用的是标准件，就没深入设计，并且在结构设计的同时，对部分零件进行加工工艺分析，最终才完成这篇毕业设计，
关键词：模具；冲裁件；凸模；凹模；凸凹模；

Answer 1

This design for the connection of the gasket with cold stamping design, according to design the size of the parts, materials, such as mass production requirements, the first part manufacturability analysis, to determine the blanking process scheme and die structure scheme, and then through the process design and calculation, determine the layout and cutting board, calculate impact pressure and pressure center, primary press, calculate convex and concave die hole size and tolerance, and in the end the design selection of parts and components, to press for check, drawing die assembly drawing, as well as to mould the major parts of the processing procedure for preparation. In the structure design, mainly to the punch and die and punch, die, positioning parts, discharge and end a device, formwork, stamping equipment, fasteners and so on design, for some parts choose standard ?
摘要
本设计为连接垫片的冷冲压设计，根据设计零件的尺寸、材料、批量生产等要求，首先分析零件的工艺性，确定冲裁工艺方案及模具结构方案，然后通过工艺设计计算，确定排样和裁板，计算冲压力和压力中心，初选压力机，计算凸、凹模刃口尺寸和公差，最后设计选用零、部件，对压力机进行校核，绘制模具总装草图，以及对模具主要零件的加工工艺规程进行编制。其中在结构设计中，主要对凸模、凹模、凸凹模、定位零件、卸料与顶出件装置、模架、冲压设备、紧固件等进行设计，对于部分零件选用的是标准件，就没深入设计，并且在结构设计的同时，对部分零件进行加工工艺分析，最终才完成这篇毕业设计，
关键词：模具；冲裁件；凸模；凹模；凸凹模；

Answer 2

Make a summary
The design for the cold stamping design gasket, according to design the size of components, materials, production requirements, first of all parts of the process analysis, to determine the plan of stamping process and die structure, and then through the calculation of process design, determine the layout and cutting board, and calculate the stamping force and the center of pressure, the primary election press, calculation the convex, concave die cutting edge size and tolerance, the final design of the parts and components, to check the press, drawing die assembly drawings, and processing technology on the main parts of the die for the preparation of the rules. In structural design, mainly carries on the design to the punch, die, punch, positioning parts, unloading and ejection device, mold, stamping equipment, fasteners and other parts, for the choice is standard, no deep design, and structure design, processing technology analysis for parts, finally completed this graduation design,
Keyword: mould; blanking; punch die; die;
百度翻译，很简单的。

Answer 3

这你还是找自己认识的英语专业的翻译吧，术语太多一般不会有人翻译的，，，

Answer 4

百度翻译 课哟

Answer 5

有道