Question

哪位高手帮忙翻译一下，网上在线翻译的就不需要了，谢谢啦，急急急！！！

1、范围
本工艺规程适用于铁磁性材料制成的压力容器及其零部件表面、近表面缺陷的磁粉检测方法。
2、引用标准
下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。在标准出版时，所示版本均
为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。
GB150－1998 钢制压力容器
JB/T 4730－2005 压力容器无损检测
3、人员资格
3.1从事磁粉检测人员，应按照《特种设备无损检测人员考核与监督管理规则》的要求取得相应无损检测资格的人员。
3.2 磁粉检测人员应从事与各自技术等级相应的工作，并负相应的技术责任。
3.3磁粉检测人员应按照压力容器有关规程、标准和本工艺，努力完成磁粉检测工作，保证检测质量。
3.4 从事磁检检测工作的人员不得有色盲、色弱。校正视力不低于1.0。
4、设备和器材
4.1设备：
质量控制应符合JB/T 4730.4－2005第3.3条要求。
4.2器材：黑磁粉、煤油、油悬浮液
质量控制应符合JB/T 4730.4－2005第3.9条要求。
5、工序安排
5.1 焊接完24小时后进行检测；
5.2 紧固件和锻件在热处理后进行检测；
5.3 应在涂漆、发蓝、磷化和电镀等表面处理之前进行检测。
6、检测工艺
6.1 检测方法：湿连续法；
6.2 磁化方法：纵向磁化和磁轭法；
6.3 磁化规范：交流电磁轭的提升力应＞44N；
6.4 灵敏度：使用15／50或30／100的A型标准试片进行综合性能试验。
7、检测操作
7.1 预处理：清理检测表面，焊缝及两则10mm的热影响区，露出金属光泽。
7.2 磁化：交叉磁轭法。移动速度30cm/分，通电时间为1－3秒，至少磁化两次，停施磁悬液3秒后，
才可停止磁化。
7.3 施加磁悬液：喷洒法。
7.4 检测方法：湿连续法，先用磁悬液润湿工件检测区表面，在通电磁化中同时施加磁悬液，待磁液形
成滞留时停止通电，进行观察、评定磁痕，被检工件表面的可见光照度＞500LX，必要时使用5－10倍
放大镜细小缺陷磁痕。
7.5缺陷磁痕的显示记录：缺陷磁痕的显示记录可采用照相、录像可剥性塑料 方式记录，同时应用草图标示。
7.6 退磁：用电磁轭局部退磁，工件上的剩磁应不大于0.2mT。
7.7 后处理：清洗掉工件表面的磁粉。
8、验收和评级
8.1 下列缺陷不允许存在
3 任何裂纹和白点；
4 任何横向缺陷显示；
5 焊缝及紧固件上任何长度大于1.5mm的线性缺陷显示；
6 锻件上任何长度大于2mm的线性缺陷显示；
7 单个尺寸大于或等于4mm的圆形缺陷显示。
8.2 磁痕评定和记录按JB/T 4730.4－2005第5条执行。
8.3 缺陷显示累积长度的等级评定按JB/T 4730－2005表6执行。
9、报告
9.1 检测报告的出具按JB/T 4730.4－2005第10条执行；
9.2 检测报告内容应正确、完整并有相应责任人签字认可。
9.3 检测送验单、检测部位及缺陷示意图，检测记录等，均作为技术资料归档保存。
9.4 检测资料须妥善保管7年，7年后，可转交用户保管。

Answer 1

1, rangeThis procedure applies to iron magnetic material pressure container and its components surface, near surface defect of magnetic particle detection method.2, reference standardsThe following normative document contains provisions which, through reference in this text, constitute provisions of this standard. In the standard was published, the editions areFor the effective. All standards are subject to revision, concerned parties using this standard should be explored using the latest edition of the following standards of possibility.GB1501998 steel pressure vesselJB / T 47302005 nondestructive testing of pressure vessels3, personnel qualification3.1 engaged in magnetic particle testing personnel, should be in accordance with the" special equipment of nondestructive testing personnel assessment and regulatory rules" requirements to obtain a corresponding qualification of nondestructive testing personnel.The 3.2 magnetic particle testing personnel should be engaged with the respective technical grade corresponding to the work, and bear corresponding responsibility for technology.The 3.3 magnetic particle inspection personnel shall be in accordance with the relevant regulations, standards of pressure vessel and the process, efforts to complete the magnetic particle testing work, ensure the test quality.Engaged in the 3.4 magnetic detection working personnel shall have the color, color blindness. Corrected visual acuity of not less than 1.4, equipment and equipmentThe 4.1 device:Quality control should be in line with the JB / T 4730.42005 article 3.3 requirements.Equipment: 4.2 black powder, kerosene, oil suspensionQuality control should be in line with the JB / T 4730.42005 article 3.9 requirements.In 5, the arrangement of process5.1 after 24 hours after the detection of welding;The 5.2 fastener and forgings after heat treatment test;5.3 should be in the painting, phosphating and Bluing, electroplating and other surface treatment before detection.6, detection technology6.1 detection methods: wet continuous method;6.2 methods of magnetization: longitudinal magnetization and magnetic yoke method;The 6.3 magnetic specification: AC electromagnetic yoke lifting force should be > 44N;The sensitivity of the 6.4 : the use of 15 / 50 or 30 / 100 of type A standard specimen for comprehensive performance test.In 7, testing operation7.1: clean the detection surface pretreatment, weld and heat affected zone of two 10mm, with metallic luster.7.2: cross magnetic yoke magnetization. The moving speed of 30cm / min, the electrifying time is at least two times 13 seconds, magnetization, stopping applying magnetic suspension after 3 seconds,It can stop the magnetization.7.3: application of magnetic suspending liquid spraying method.7.4 detection methods: wet continuous method, first with a magnetic suspension liquid wetting workpiece surface in the detection zone, through electromagnetic and application of magnetic suspending liquid, the magnetic liquidBecome stranded when stopping electrifying, observation, evaluation of magnetic marks, the surface subject to inspection by visible light illumination > 500LX, use when necessary 510 timesMagnifying small defects magnetic mark.7.5 defects of magnetic trace display recording: defect magnetic display records by photographic, video strippable plastic records, while the application of draft mark.7.6: local demagnetization demagnetization using electromagnetic yoke, workpiece remanence should be less than 0.2mT.7.7 after treatment : clean the workpiece surface magnetic powder.8, acceptance and ratingIn 8.1 the following defects will not allow the existence of3 any cracks and flaking;4 any lateral defect display;5 seam and fasteners of any length greater than 1.5mm linear defects;6 forging any length greater than 2mm linear defects;The 7 single size greater than or equal to 4mm Round flaw display.The 8.2 magnetic evaluation and records in the JB / T 4730.42005 fifth implementation.The 8.3 flaw display the cumulative length of grading according to JB / T 47302005 table 6 executive.9, report9.1 testing report issued by JB / T 4730.42005 tenth implementation;The 9.2 inspection report content should be correct, complete and have the corresponding responsibility person authorized signature.9.3 detection for examination, testing and defect of single parts diagram, test records, both as a technical data archiving.9.4 test data shall be properly maintained for 7 years, after 7 years, can be transmitted to the user.

Answer 2

是啊 要花钱的 给钱的话还是可以考虑的

Answer 3

宝贝儿，这么专业这么多，要花银子的。