Question

请帮我翻译一篇文章，谢谢了！！！

本机器特点：
1、稳固操作机构，防止不当外力造成已回焊后的PCB锡道面、焊点等回路破坏。
2、机器台上端的下部配置有日光灯, 以防在阴影环境下操场时的
工作误差，配置有计数器功能（可加装皮带线的CUT—3T）。
3、以直线式滚动性压迫性切断V槽式塑胶板或各式纤维板，彻底防范焊点的损伤和断裂。
4、特殊行程式滑轨式切断方式，确保切断面之平滑度
5、切割行程距离采取触控式五段调整，可分四个行程，以方便最佳运用不同刀面的磨损程度。
6、本机配有两种速度，单程，来回程方式切断供选择。
7、安装防切手指电子眼保护装置，避免人为不当时的伤害。
8、 CUT--3T的为送料延长型工作方式，在PCB切完后可通过皮带线直接延长到检验流水线上。

技术参数：
1、外观尺寸：700×330×400mm
2、机身重量： CUT--3：70公斤
3、工作电压：AC 220V
4、总耗电量：150W
4、可切最小：V-CUT槽至0.2mm，元件与板槽距离最小1.00mm。
5、切刀行程：最大400mm，其它依次是100mm；200mm；300mm。
6、切板高度：可切割PCB板元件的高度：最高为35 mm。
希望专业人士帮忙，不要随便找个翻译软件直接翻译，那样是不行的！！谢谢

Answer 1

The machine features:
1, stable operation, prevent external cause has returned after soldering tin road surface, solder PCB loop. Etc.
2, the bottom on the machine is equipped with fluorescent lamp, just in the shadow of the working environment, with a counter error function (can add how 3T -- the belt line).
3 and ZhiXianShi oppressive cut V rolling of plastic board or groove joints, completely prevent various fiberboard damage and fracture.
4 and special trip type slippery course type, cut off to ensure the smoothness
5 and cutting trip distance to touch consists of four points, can adjust to the best use convenient wear different knife.
6 and the speed with two ways, one for choice charges, cut off.
7 and install anti cut fingers, avoid factitious electron optics protection device was not hurt.
8 and how to extend the feeding 3T - type, after cutting in PCB line can be extended to direct belt through inspection line.

Technical parameters:
1, 700 appearance size: 400mm x x 330
2, then how fuselage weight: - 0 kilograms
3, a working voltage: AC 220V
4, total consumption of 150W:
4, can CUT the minimum: V - how to 0.2 mm, component slot with minimum 1.00 mm board slot.
5 and cutting knife trip: maximum 400mm and other 100mm is, 200mm, 300mm.
6 and cutting plate height: cutting board components for 35 mm: highest altitude.
回答者： 82724929 - 试用期 一级 4-17 17:35
This machine features:
1, a solid operating agencies, to prevent the misuse has been caused by external force to the PCB after soldering tin pavement, solder joints, such as damage to circuits.
2, the platform side of the lower part of the machine is equipped with fluorescent lamps to prevent the circumstances in the shadow of the playground at the time of
The work of error, is equipped with counter function (which can be retro-fitting belt line CUT-3T).
3, the rolling of a linear compression V trough cut all kinds of plastic board or fibreboard and thoroughly to prevent injury and fracture of the solder joint.
4, the special line type cut slide program to ensure the smoothness of cut surface
5, cutting travel distance to take a touch adjustment five in four trips to facilitate the best use of a different degree of flank wear.
6, the machine is equipped with two speed, one-way to return the way for the choice of cut off.
7, the installation of anti-E-finger cut eye protection devices to prevent harm to people who do not at that time.
8, CUT - 3T extended for feed-type work, after cutting the PCB can be directly extended to the belt line on the test line.

Technical parameters:
1, Size: 700 × 330 × 400mm
2, body weight: CUT - 3: 70 kilograms
3, work voltage: AC 220V
4, the total power consumption: 150W
4, may be the smallest cut: V-CUT slot to 0.2mm, slot board components and the smallest distance 1.00mm.
5, Cutter trip: Maximum 400mm, followed by 100mm; 200mm; 300mm.
6, cutting board Height: PCB board can be cut the height of components: a maximum of 35 mm.

Answer 2

This machine features:
1, a solid operating agencies, to prevent the misuse has been caused by external force to the PCB after soldering tin pavement, solder joints, such as damage to circuits.
2, the platform side of the lower part of the machine is equipped with fluorescent lamps to prevent the circumstances in the shadow of the playground at the time of
The work of error, is equipped with counter function (which can be retro-fitting belt line CUT-3T).
3, the rolling of a linear compression V trough cut all kinds of plastic board or fibreboard and thoroughly to prevent injury and fracture of the solder joint.
4, the special line type cut slide program to ensure the smoothness of cut surface
5, cutting travel distance to take a touch adjustment five in four trips to facilitate the best use of a different degree of flank wear.
6, the machine is equipped with two speed, one-way to return the way for the choice of cut off.
7, the installation of anti-E-finger cut eye protection devices to prevent harm to people who do not at that time.
8, CUT - 3T extended for feed-type work, after cutting the PCB can be directly extended to the belt line on the test line.

Technical parameters:
1, Size: 700 × 330 × 400mm
2, body weight: CUT - 3: 70 kilograms
3, work voltage: AC 220V
4, the total power consumption: 150W
4, may be the smallest cut: V-CUT slot to 0.2mm, slot board components and the smallest distance 1.00mm.
5, Cutter trip: Maximum 400mm, followed by 100mm; 200mm; 300mm.
6, cutting board Height: PCB board can be cut the height of components: a maximum of 35 mm.

Answer 3

The machine features:
1, stable operation, prevent external cause has returned after soldering tin road surface, solder PCB loop. Etc.
2, the bottom on the machine is equipped with fluorescent lamp, just in the shadow of the working environment, with a counter error function (can add how 3T -- the belt line).
3 and ZhiXianShi oppressive cut V rolling of plastic board or groove joints, completely prevent various fiberboard damage and fracture.
4 and special trip type slippery course type, cut off to ensure the smoothness
5 and cutting trip distance to touch consists of four points, can adjust to the best use convenient wear different knife.
6 and the speed with two ways, one for choice charges, cut off.
7 and install anti cut fingers, avoid factitious electron optics protection device was not hurt.
8 and how to extend the feeding 3T - type, after cutting in PCB line can be extended to direct belt through inspection line.

Technical parameters:
1, 700 appearance size: 400mm x x 330
2, then how fuselage weight: - 0 kilograms
3, a working voltage: AC 220V
4, total consumption of 150W:
4, can CUT the minimum: V - how to 0.2 mm, component slot with minimum 1.00 mm board slot.
5 and cutting knife trip: maximum 400mm and other 100mm is, 200mm, 300mm.
6 and cutting plate height: cutting board components for 35 mm: highest altitude.